| Crown XTi 2002 Power Amplifier Specifications: |
2Ω Stereo (per ch.) : 1000W
4Ω Stereo (per ch.) : 800W
8Ω Stereo (per ch.) : 475W
8Ω Bridge-Mono : 1600W
4Ω Bridge-Mono : 2000W
|
| Input EQ |
6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.
|
| Crossover Filters |
Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control.
|
| Output EQ |
8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed.
|
| Delay |
For signal alignment of driver; 50 mS of total delay.
|
| SubHarmonic Synth |
Takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type.
|
| Peakx Plus Limiter |
User defeatable limiter that allows users to control Threshold, Attack, and Release times.
|
| Presets |
30 total presets, 29 of which are user-definable.
|
| Sensitivity (for full rated power at 4 ohms) |
1.4 Vrms
|
| Frequency Response (at 1 watt, 20 Hz - 20 kHz) |
+0 dB, –1 dB
|
| Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms) |
XTi1002/2002/4002: 100 dB (A weighted)
|
| Total Harmonic Distortion (THD) |
< 0.5%
|
| Damping Factor 20 Hz to 1 kHz |
> 500
|
| Crosstalk (below rated power) |
20 kHz - 1 kHz: > 70 db
|
| Input Impedance (nominal) |
20k ohms balanced, 10k ohms unbalanced
|
| Maximum Input Signal |
+22 dBu typical
|
| AC Line Voltage and Frequency Configurations |
100 VAC, 120 VAC, 220-240 VAC 50/60 Hz
|
| AC Line Current (120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch) |
XTi2002: 8.3A; no more than 38W at idle
|
| Operating Temperature |
0°C to 40°C at 95% relative humidity (non-condensing)
|
| Level |
Two front-panel rotary level controls, one for each channel
|
| Power Switch |
On/Off switch applies AC power to the amplifier
|
| Sel/Prev/Next Buttons |
Three buttons near the LCD screen that are used to access menu items and front panel lockout
|
| LCD Screen |
Backlit liquid crystal display that shows preset and processing status
|
| Signal Indicator |
Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
|
| –10 Indicator |
Green LED flashes when output signal exceeds -10 dB below clip.
|
| –20 Indicator |
Green LED flashes when output signal level exceeds -20 dB below clip.
|
| Ready Indicator |
Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
|
| Clip Indicator |
Red LED, one per channel, turns on at the threshold of audible distortion
|
| Temp Indicator |
Red LED, one per channel, illuminates under excessive temperature conditions
|
| Power Indicator |
Blue LED illuminates when the amplifier has been turned on and has power
|
| Input Connectors |
XLR, one per channel
|
| Link/Out Connector |
Loop-thru signal from input connector for linking another amplifier, one per channel.
|
| Output Connectors |
Two Neutrik® Speakon® NL4MP output connectors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors).
|
| HiQnet USB Connector |
Type B, connects to HiQnet network.
|
| Chassis |
Steel
|
| Front Panel |
Cast-aluminum
|
| Cooling |
Proportional speed fan with front-to-rear airflow.
|
| Dimensions |
XTi 1002/2002/4002: 19" (W) x 3.5" (H) x 12.25" (D)
|
| Net Weight |
XTi 1002/2002/4002: 18.5 lbs (8.4kg)
|
| Shipping Weight |
XTi 1002/2002/4002: 21.5 lbs (9.8kg)
|
