| Crown XTi 6002 Power Amplifier Specifications: |
| 2Ω Stereo (per ch.) : 3000W
4Ω Stereo (per ch.) : 2100W
8Ω Stereo (per ch.) : 1200W
8Ω Bridge-Mono : 4200W
4Ω Bridge-Mono : 6000W |
| Input EQ |
| 6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed. |
| Crossover Filters |
| Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control. |
| Output EQ |
| 8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed. |
| Delay |
| For signal alignment of driver; 50 mS of total delay. |
| SubHarmonic Synth |
| Takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type. |
| Peakx Plus Limiter |
| User defeatable limiter that allows users to control Threshold, Attack, and Release times. |
| Presets |
| 30 total presets, 29 of which are user-definable. |
| Sensitivity (for full rated power at 4 ohms) |
| 1.4 Vrms |
| Frequency Response (at 1 watt, 20 Hz - 20 kHz) |
| +0 dB, –1 dB |
| Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms) |
| XTi6002: 103 dB (A weighted) |
| Total Harmonic Distortion (THD) |
| < 0.5% |
| Damping Factor 20 Hz to 1 kHz |
| > 500 |
| Input Impedance (nominal) |
| 20k ohms balanced, 10k ohms unbalanced |
| Maximum Input Signal |
| +22 dBu typical |
| AC Line Voltage and Frequency Configurations |
| 100 VAC, 120 VAC, 220-240 VAC 50/60 Hz |
| AC Line Current (120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch) |
| XTi6002: 15.3A; no more than 180W at idle |
| Operating Temperature |
| 0°C to 40°C at 95% relative humidity (non-condensing) |
| Level |
| Two front-panel rotary level controls, one for each channel |
| Power Switch |
| On/Off switch applies AC power to the amplifier |
| Sel/Prev/Next Buttons |
| Three buttons near the LCD screen that are used to access menu items and front panel lockout |
| LCD Screen |
| Backlit liquid crystal display that shows preset and processing status |
| Signal Indicator |
| Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs). |
| –10 Indicator |
| Green LED flashes when output signal exceeds -10 dB below clip. |
| –20 Indicator |
| Green LED flashes when output signal level exceeds -20 dB below clip. |
| Ready Indicator |
| Green LED, one per channel, illuminates when the amplifier is ready to produce audio. |
| Clip Indicator |
| Red LED, one per channel, turns on at the threshold of audible distortion |
| Temp Indicator |
| Red LED, one per channel, illuminates under excessive temperature conditions |
| Power Indicator |
| Blue LED illuminates when the amplifier has been turned on and has power |
| Input Connectors |
| XLR, one per channel |
| Link/Out Connector |
| Loop-thru signal from input connector for linking another amplifier, one per channel. |
| Output Connectors |
| Two Neutrik® Speakon® NL4MP output connectors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors). |
| HiQnet USB Connector |
| Type B, connects to HiQnet network. |
| Chassis |
| Steel |
| Front Panel |
| Cast-aluminum |
| Cooling |
| Proportional speed fan with front-to-rear airflow. |
| Dimensions |
| XTi 6002: 19" (W) x 3.5" (H) x 16.2" (D) |
| Net Weight |
| XTi 6002: 24.0 lbs (10.9kg) |
| Shipping Weight |
| XTi 6002: 30.0 lbs (13.6kg) |
